A spray gun lays primer and enamel down as fine mist in thin, level passes, and the dried film is level instead of ridged. Cabinet spray painting is the reason a finish reads as factory work rather than as a paint job.
Doors and drawer fronts leave the house for a filtered booth where dust and temperature are controlled, and the boxes are sprayed in place behind sealed containment. That split matters more in a Hamilton condo or a narrow Corktown galley than anywhere else, because the unit stays livable with the doors away.
Brushed Cabinet Painting Leaves Marks That Never Disappear From A Door
Cabinet spray painting exists because a brush cannot lay an even film on a raised panel. A brush drags ridges along the stiles, loads the corners of the panel and leaves a thick edge that chips at the first knock.
A roller adds stipple instead, a fine orange peel texture that catches every bit of under-cabinet lighting. Sprayed cabinet painting puts down a much thinner film per coat, and thin coats are harder, level better and hold their edges. Two or three of them with a light sand between beat one thick brushed coat every time.
Cabinet Painting Happens In A Booth For Doors And In The House For Boxes
The two halves of a cabinet painting job happen in two places for good reasons. In the booth, doors lie level or hang vertical in filtered air held at a steady temperature, which is what allows a coat to flow out without dust landing in it.
Boxes and face frames cannot travel, so that half of the cabinet painting happens on site. That means plastic sheeting sealed floor to ceiling, counters and appliances covered, the floor protected, and controlled ventilation while the coats go on. Neighbouring rooms stay masked until the containment comes down.
Cabinet Painting Products Fall Into Two Families That Behave Differently
The cabinet painting product is chosen for the kitchen, not out of habit. Waterborne alkyd enamels level beautifully, come in thousands of colours and are low-VOC, but they recoat slowly and want roughly a week before normal use, with full hardness closer to a month.
Two-component polyurethanes mix a hardener into the coating and are sprayed only. They sand in about two hours, stack in five and are hard within a day, which is why they suit a kitchen that has to be back in service fast. Two-component cabinet painting also costs more, because unused mixed product has a pot life of a few hours and is wasted if the day runs short.
Humidity is the other factor. Waterborne cabinet painting cures slowly in the sticky harbour air of July and August, so summer jobs get more time between coats rather than being pushed.
Sprayed Cabinet Painting Costs More Than Brushed And Lasts Longer
The premium for sprayed cabinet painting generally runs several hundred dollars on a kitchen, and it buys equipment, containment, booth time and transport. Brushed work on cabinets typically holds three to five years before it looks tired, while sprayed work is reported at ten years and beyond.
Spraying is also what makes deep colours workable. Navy, forest green and charcoal each need an extra coat to cover evenly, and a third brushed coat on a raised panel door would be visible from across the room. Those colours come up constantly in two-tone kitchens and island painting.
Ask About Cabinet Spray Painting For Your Kitchen
Every cabinet painting quote states where each part is sprayed, which product family is used and how many coats it gets. The cabinet spray painting visit and the written quote cost nothing. Call +1 (289) 201-5389, book a time through the contact page or read how the whole process runs.
Cabinet Spray Painting Questions
Why spray instead of brush?
Brushing leaves ridges that show under kitchen lighting. A spray gun lays thin, level coats, and deep colours cover evenly. Brushed work typically holds three to five years, while sprayed work is reported at ten years and beyond.
What paint is used for spraying cabinets?
Two families are in normal use. Waterborne alkyd enamels level well and come in thousands of colours. Two-component polyurethanes mix in a hardener and cure harder and faster. Both are low-VOC, and the quote names the one your kitchen gets.
Where does the spraying happen?
Doors and drawer fronts go to a filtered booth where dust and temperature are controlled. Boxes and face frames cannot move, so they are sprayed in the house behind sealed plastic with ventilation set up.